Skip to main content

[Webinar] Meeting Specs for Safety: The Role of Material Properties Assurance

Published by
Energy Global,


When a natural gas pipeline ruptured in California in 2010, the response from an industry that prioritizes safety was immediate. And even eight years later, regulatory focus continues on one of the accident’s root causes: Insufficient material properties knowledge.

As investigators discovered, the section where the rupture occurred had been cobbled together from various pipe segments of unknown specifications. There was no material property information for the segments, although there was little question they weren’t made of the seamless, high-grade steel the operator’s as-built drawings indicated.

[Webinar] Meeting Specs for Safety: The Role of Material Properties Assurance

Register Now »

To help prevent a similar tragedy, the industry set out to address the need for traceable, verifiable and complete pipeline records. This started with the Integrity Verification Process (IVP) and has resulted in additional material properties requirements for gas transmission lines in High Consequence Areas, which are expected to be released by the Pipeline and Hazardous Materials and Safety Administration (PHMSA) in March 2019. Among the new requirements will be the verification of pipe materials.

In Europe, pipeline condition assessment activities have also ramped up, especially when it comes to ageing pipelines. Some companies, including a major Dutch natural gas operator, have increased the standards for equipment that will be permanently installed on their lines, such as hot tap fittings.

In this webinar, T.D. Williamson (TDW) Product Line Director Rich Kehl will examine the effect of material properties assurance on integrity and help operators prepare for the new regulations ahead.

Specifically, he will discuss:

  • Why all equipment installed on a line must maintain pipeline material property assurance.
  • The anatomy and function of the hot tap fitting.
  • The critical importance of material properties and compatibility when choosing a hot tap fitting.
  • Why the manufacturing method matters when choosing a hot tap fitting.
  • The benefits and challenges of fabricating and extruding hot tap fittings.
  • How to ensure weld quality during fitting manufacture.
  • How to limit the number of welds on the pipeline.

Kehl will also talk about one of the most significant issues concerning operators today: What do you do if you don’t know the material property of your pipeline to begin with?

Register Now »

Pipelines constructed in the last 10 to 20 years should have traceable, verifiable and complete records, including hydrostatic test reports, MAOP validation and mill-test reports for specific pipe lots. But what about ageing assets, specifically those installed prior to 1970? According to PHMSA, 59 percent of U.S. gas transmission pipelines fall into that category, meaning there’s significant potential for missing records. In fact, in 2016, natural gas operators in the United States reported that 7.242 kilometers (4,500 miles) of pipe in High Consequence Areas and Class 3 and 4 locations had inadequate records to confirm maximum allowable operating pressure.

The issue is equally urgent outside of the U.S. For example, based on CONservation of Clean Air and Water in Europe (CONCAWE) data, 47 percent of the assets they cover were installed prior to 1970. And while it does not explicitly contain specific data on percentage of pipelines installed prior to 1970, the European Gas Pipeline Incident Data Group’s (EGIG) ninth report published in February 2015 does address the influence of the age of pipelines on their failure frequencies.

Kehl will describe an innovative method for overcoming missing or incomplete pipeline data in ageing assets. By incorporating the TDW Pipe Joint Classification process, this approach recreates important pipe material records. In addition, it improves confidence that the operator has applied the appropriate level of risk to specific pipe joints and segments.

About our presenter

Rich Kehl holds degrees in Engineering Sciences from Dartmouth College, Mechanical Engineering from Stanford University and Aeronautics and Astronautics from the Massachusetts Institute of Technology. He joined TDW as Product Director – Hot Tapping & Plugging in 2017. Kehl leads the strategic direction of the product and service lines, facilitating a team composed of product management, sales, engineering, manufacturing, and service operations. Prior to TDW, Kehl managed global product portfolios of GE’s power generation equipment, power plant configuration, and air quality components.

Read the article online at: https://www.energyglobal.com/pipelines/equipment-and-safety/17092018/webinar-meeting-specs-for-safety-the-role-of-material-properties-assurance/

 

Embed article link: (copy the HTML code below):